Chemical Feed Skids / Liquid Polymer Feeders

Series 6000 liquid polymer feeders use the energy available in the dilution water stream to provide the energy for polymer activation. The Series 6000 provides the high energy levels needed to effectively activate all liquid polymers.  The Series 6000-A is specifically engineered for systems that have low polymer feed rates.  The Series 6000-PC is for systems that have high polymer feed rates or require the reliability of a progressive cavity metering pump.

TECHNICAL INFORMATION Series 6000

• The Series 6000 Polymer Feeder provides the high energy needed to effectively activate all liquid polymers.
• The polymer metering pump is a solenoid operated diaphragm pump.  It is available with manual or external control.  The externally controlled pump can accept a 4-20 mA or a pulse signal.
• The dilution water can be clean or filtered process water.
• A low water flow switch is standard on all Liquid Feeders.  It stops the metering pump whenever the water flow drops below minimum.  The pump automatically restarts when adequate water flow resumes.
• The sight tube is self-cleaning.  The flow of the solution leaving the activating apparatus causes the patented cleaning assembly to operate continuously.  The sight tube allows the operator to see how the feeder is operating.
• The external injection valve is accessible without disturbing the activating apparatus.
• Motor-less activation injects the polymer into the water stream and immediately makes the solution flow through a low pressure, high energy polymer activation nozzle.  The nozzle self compensates for solution flow fluctuations.  This assures that the polymer activation energy level remains adequate as the solution flow changes.
• It's designed to be maintenance free.  All components are modular and easy to access.  There are no parts to wear out and no mixer motors to burn out.                                                            
• A water strainer is standard with each mixer.  The strainer collects debris that may clog the flowmeter or other components.
• A pump calibration cylinder is standard with each mixer.  The cylinder is prepiped with isolation valves to allow checking the metering pump flow rate.
• All components are corrosion resistant.  The mixer support frame is made welded stainless steel.  

STANDARD FEATURES

• Polymer feed capacities of 0.1 to 240 GPD (0.02 to 38 l/h).
• Dilution water capacities of 20 to 1200 GPH (75 to 4500 l/h).
• Easily accessed injection valve.
• Motorless mixing system.  
• Self cleaning sight glass (Patented).
• Dilution water pressure range capacity of 20 to 100 psi (1.4 to 6.8 bar).
• Polymer pump stops when dilution water flow drops below minimum.
• Prepiped metering pump calibration cylinder system.
• All components are easily accessed.
• Water strainer.
• A drain valve allows complete flushing of the feeder.
• Compact, most units are 15"W x 15"H x 21"D (38 cm x 38 cm x 53 cm).
• Lightweight, most units weigh less than 50 lbs (23 kg).
• Electrical service: 120/240 VAC; 50/60 Hz; less than 300 watts.

TECHNICAL INFORMATION 6000 A

• The Series 6000A Polymer Feeder is engineered for low polymer feed applications, where the anticipated feed rate is less than 24 GPD.  It provides the high energy needed to effectively activate all liquid polymers.
• The polymer metering pump is a solenoid operated diaphragm pump.  It is available with manual or external control.  The externally controlled pump can accept a 4-20 mA or a pulse signal.
• A low water flow switch is standard on all Liquid Feeders.  It stops the metering pump whenever the water flow drops below minimum.  The pump is automatically restarted when adequate water flow resumes.
• A blending - aging chamber provides improved polymer effectiveness.
• The sight tube is self-cleaning.  The flow of the solution leaving the activating apparatus causes the patented cleaning assembly to operate continuously.  The sight tube allows the operator to see how the feeder is operating.
• The external injection valve is accessible without disturbing the activating apparatus.
• Motor-less activation injects the polymer into the water stream and immediately makes the solution flow through a low pressure, high energy polymer activation nozzle.  The Patented nozzle self-compensates for solution flow fluctuations.  This assures that the polymer activation energy level remains adequate as the solution flow changes.
• It's designed to be maintenance free.  All components are modular and easy to access.  There are no parts to wear out and no mixer motors to burn out.  
• A pump calibration cylinder is standard with each mixer.  The cylinder is prepiped with isolation valves to allow checking the metering pump flow rate.
• All components are corrosion resistant.  The support frame is made of welded stainless steel.  

STANDARD FEATURES

• Polymer feed capacities of 0.1 to 24 GPD (0.02 to 3.8 l/h).
• Dilution water capacities of 10 to 300 GPH (40 to 1140 l/h).
• Blending / Aging chamber for improved polymer effectiveness.
• Primary and Secondary dilution water flows
• Easily accessed injection valve.
• Motorless mixing system.  
• Self cleaning sight glass (Patented).
• Dilution water pressure range capacity of 20 to 100 psi (1.4 to 6.8 bar).
• Polymer pump stops when dilution water flow drops below minimum.
• Prepiped metering pump calibration cylinder system.
• All components are easily accessed.
• Compact, most units are 18"W x 16"D x 21"H (46 cm x 41 cm x 53 cm).
• Lightweight, most units weigh less than 50 lbs (23 kg).
• Electrical service: 120/240 VAC; 50/60 Hz; less than 300 watts.

OPTIONS:

• "J" - Solenoid water control valve.
• "S" - Programmable pump.
• *  Pump controlled by dilution water flow.  Maintains solution concentration.
• *  Explosion Proof for Class1, Group D installations.
• *  Other voltages.
• *  Custom modified to meet your needs.

TECHNICAL INFORMATION 6000 PC

• The Series 6000PC Polymer Feeder provides the high energy needed to effectively activate all liquid polymers.
• The polymer metering pump is a Progressive Cavity Pump.  It is available with manual or external control.  The externally controlled pump can accept a 4-20 mA signal.
• The dilution water can be clean or filtered process water.
• A low water flow switch is standard on all Liquid Feeders.  It stops the metering pump whenever the water flow drops below minimum.  The pump is automatically restarted when adequate water flow resumes.
• The sight tube is self-cleaning.  The flow of the solution leaving the activating apparatus causes the patented cleaning assembly to operate continuously.  The sight tube allows the operator to see how the feeder is operating.
• The external injection valve is accessible without disturbing the activating apparatus.
• Motor-less activation injects the polymer into the water stream and immediately makes the solution flow through a low pressure, high energy polymer activation nozzle.  The nozzle self compensates for solution flow fluctuations.  This assures that the polymer activation energy level remains adequate as the solution flow changes.
• It's designed to be maintenance free.  All components are modular and easy to access.  There are no parts to wear out and no mixer motors to burn out.  
• A water strainer is standard with each mixer.  The strainer collects debris that may clog the flowmeter or other components.
• A pump calibration cylinder is standard with each mixer.  The cylinder is prepiped with isolation valves to allow checking the metering pump flow rate.
• All components are corrosion resistant.  The support frame is made of welded stainless steel.  

STANDARD FEATURES

• Polymer feed capacities of 2.5 to 840 GPD (0.4 to 133 l/h).
• Dilution water capacities of 30 to 3600 GPH (115 to 13600 l/h).
• Motorless mixing system.  
• A patented high energy nozzle activates the polymer.  
• The nozzle self-compensates for changes in water flow.
• Self cleaning sight glass (Patented).
• Dilution water pressure range capacity of 20 to 100 psi (1.4 to 6.8 bar).
• Polymer pump stops when water flow drops below minimum.
• Pump calibration cylinder system.
• All components, including the injection valve, are easily accessed.
• Stainless steel welded frame.
• Compact, most units are 24"W x 30"H x 18"D (61cm x 76 cm x 46 cm).
• Lightweight, most units weigh less than 90 lbs (41 kg).
• Electrical service: 120/240 VAC; 50/60 Hz; less than 600 watts.
• Most units can be rented.  Most of the rent is applied towards purchase. 

OPTIONS:

"G" - Pump speed controlled by dilution water flow, maintains solution concentration.
"J" - Solenoid water control valve.
"T" - Dilution water flow of 90 to 1200 GPH ( 340 to 4500 l/h ).
"V" - Dilution water flow of 120 to 1800 GPH ( 450 to 6800 l/h ).
"W" - Dilution water flow of 180 to 3600 GPH ( 700 to 24000 l/h ).

MOTORLESS ACTIVATION

• High energy, motorless, polymer activatiion apparatus.
• Acivates all liquid polymers.
• Effectively uses the energy available in the dillution water.
• Polymer is injected with the dillution water through the patented, high energy, activation nozzle.
• Self compinsates for flow fluccuations.
• Assures the polymer activation energy levels remain constant.
• Accelerates the solution to 40 ft./sec.
• Generates very high activation energy.
• Exposes the polymer to the activation energy only once.